22mm 3D Models

Find the best 22mm 3D Models, free download in STL, FBX, GLB, OBJ, 3MF, USDZ for 3D modeling and creation in Blender, 3D printing, game developing, animation, eCommerce, AR/VR and etc. Generated by Tripo AI 3D Generator.

You May Also Like :

Anonymous1773136078

圆柱形杆长度(200)mm，杆身外径(14)mm，底部有椭圆插接头长轴(22)mm、短轴(14)mm，长度(40)mm。

Anonymous1775445856

圆柱形杆总长度(200)mm，杆身外径(14)mm，底部插接头适配长轴(22)mm、短轴(14)mm的婴儿车椭圆安装孔，插接头长度(40)mm。

Anonymous1775445856

Football figure. 22mm in height. Standing on a 6.5mm diameter base and a 3.5mm x 4mm high pin underneath the 6.5mm base

Anonymous1758365389

letra O , respeta las medidas de la imagen , solo la parte azul, los lados superior e inferior son de 16mm de espezor, las partes laterales son de 22mm de espesor, profundidad 5mm , frente y atras superficies planas, eliminar fondo y lineas rojas

Anonymous1749938580

根据右边生成的模型，宽度改为2.1cm，中间厚度3mm，过渡到边缘的厚度为1.5mm

Anonymous1769067497

创建一个圆形浅盘 3D 模型，总直径 250mm，总高度 22mm，盘边厚度 5mm，盘底厚度 4mm，所有尖锐边缘均做 R3 圆角倒角处理。盘面由一条直线分隔为左右两区，分隔线从圆心向右偏移 31mm，左侧盛菜区有效直径 162mm，右侧蘸料区有效直径 88mm。左右两区存在高度差台阶，台阶不做垂直直角，改为自然斜面过渡，斜度约 26.5°，台阶高度 4mm，台阶边缘做 R1.5 顺滑倒角。左侧盛菜区表面做均匀条纹凹槽，条纹方向与分隔线严格垂直，呈水平走向，条纹宽度 3.5mm，间距 3mm，深度 1.5mm。整体材质为哑光白瓷，表面细腻温润，无反光、无瑕疵，干净简约，光影柔和，结构清晰。

Anonymous1745197233

a circular cover for the cgm sensor with diameter of 22mm and a height of 2–4.2mm

Anonymous1773253889

cilindro hueco 22mm de diametro con rosca ,20 mm de alto y en la parte superior una tapa de 3mm de alto y de 30mm de diametro con un chaflan

Anonymous1772070852

Anonymous1768306088

preciso fazer uma peca para fixar um par de setas em um cano de 80mm e as setas tem uma rosca de 9mm entao quero fazer esssa peca que ao olhar ela de frente teremos uma especie de cruz onde a peca vertical tem um diametro interno de 51mm externa de 800 ,ja na horizontal teremos um diametro interno de 9mm e externo de 22mm , o tubo vertical tera 80mm de altura e o horizontal tera apartir do tubo vertical 50mm para cada lado crie um desiner onde a transicao de cada diametro seja organica,e se possivel o tubo vertical seja feito de forma bipartido para facilitar a instalacao de um outro tubo que ira sustentar a peca

Geotec

Anonymous1764857785

UN CYLINDRE DE 60mm de long et 22mm de diametre avec un trou au milieu de 12 mm de diamètre et 40mm de profondeur d'un coté, et de l'autre coté au sommet une boule de pétanque en décoration

Anonymous1768941251

AN 44MM AND 22MM TALL CUP CIRCLE NO HANDLE

Anonymous1768934512

параллелепипед 73 миллиметра длинна, 33 миллиметра ширина, 2 миллиметра толщина . смещение длинных граней относительно друг друга 10 миллиметров

Anonymous1765551606

Geometry and sizeI want a simple 3d plate the is 22mm tall and 56mm long, I want the depth of this plate to be 5mm. Along each edge of this plate i want a 1mm chamfer. In the center of the plate i want a through all countersink hole that conforms to a ANSI Metric, Flat Head Screw - ANSI B18.6.7M size M4, Then on both sides of the center hole 11.5mm away i want simple through all holes with a diameter of 4mm

Solid rectangular plate, overall 56 mm (length, X) × 22 mm (height, Y) × 5 mm (thickness, Z).
Coordinate frame: the plate is sketched on the XY plane and extruded +Z.
Edge finishing

1 mm fillets applied to all outer edges:
Top and bottom perimeter edges (around the END and START faces).
All four vertical corner edges (between the side faces).
Holes

Center hole: through, countersunk for an ANSI Metric flat head screw M4 (B18.6.7M).
Countersink: 90° included angle, 9.4 mm major diameter.
Pilot/through: 4.5 mm (normal clearance for M4).
Located at the plate center (0, 0).
Two “outer” simple through-holes (

Anonymous1769653037

A 22mm long cylinder has ends measuring 6mm and 6.5mm respectively, meeting proportionally in the middle.

Anonymous1754000844

Anonymous1752040679