?

Dispenser 3D Models

Find the best Dispenser 3D Models, free download in STL, FBX, GLB, OBJ, 3MF, USDZ for 3D modeling and creation in Blender, 3D printing, game developing, animation, eCommerce, AR/VR and etc. Generated by Tripo AI 3D Generator.

You May Also Like :
soappumptapepill
Anonymous1776728014
Anonymous1776717359
Anonymous1776673595
quiero un dispensador de jabon liquido que un envase para el jabon y una caja en la parte trasera para un circiuto adaptado para que sea automatico ,en donde cae el jabon quiero que tenga orificios para que pase una maguera quirurgica y que en la parte de abajo del dispensador tenga una regilla para recoger los sobrantes , que su altura se de 20cm y su ancho de 15cm . el tanque de jabon de 2l de capacidad, vasate en el diseño de la imagen , que tenga lugar por donde salga el jabon como un dispensador normal pero que este funcione con una bomba y un lugar para donde entre una bomba de agua para poder sacar el jabon y no olvides el compartimento para los componentes electronicos quiero que se divida en cuatro partes separadas dejando ver adentro del dispensador y poder ver su distribucion de compartimentos
Anonymous1776307554
Anonymous1766942160
make me a tea bag dispenser that can hold 20 or more tea bags. It should be able to let you pull one tea bag out at a time and it has to be two separate prints, a lid that fits on scurly but you can take off to refil the tea bags, and the body which will hold the tea bags and let you pull one out at a time. The body should be a tall rectangle and it should be full close with no open holes on the side. Just make sure there is a hole at the top to refill it and the lid can snap on and off.
Anonymous1776511117
Anonymous1776516181
Rustam Pulatov
Ok fix it by adding a full rectangle around where the tea bags will be held and make the words Tea Bags in English. One tea bag at a time you can pull out at a time. This should be a tea bag dispenser with a body and dispenser with a separate part, a lid and it should hold tea bags in a rectangle column.
Anonymous1776511117
Create a compact, 3D-printable tea bag dispenser with two parts: a main body and a removable lid. The body must store at least 20 standard rectangular tea bags stacked neatly on top of each other in a vertical rectangular column tower. The interior should be narrow and slightly tapered or include guide rails to keep the tea bags aligned, upright, and stable so they do not tilt or shift. Include a gravity-fed dispensing slot at the lower front that allows only one tea bag to be pulled out at a time. Add a small internal lip above the opening to prevent multiple tea bags from coming out together. The lid must fit tightly using a friction or snap fit but remain easy to remove for refilling. Add the words “Tea Bags” in bold English text cut through the front wall. Use smooth surfaces, rounded edges, a flat base, and ensure it prints without supports. Add a front plate so the tea bags dont fall out
Anonymous1776511117
Create a compact, 3D-printable tea bag dispenser with two parts: a main body and a removable lid. The body must store at least 20 standard rectangular tea bags stacked neatly on top of each other in a vertical rectangular column tower. The interior should be narrow and slightly tapered or include guide rails to keep the tea bags aligned, upright, and stable so they do not tilt or shift. Include a gravity-fed dispensing slot at the lower front that allows only one tea bag to be pulled out at a time. Add a small internal lip above the opening to prevent multiple tea bags from coming out together. The lid must fit tightly using a friction or snap fit but remain easy to remove for refilling. Add the words “Tea Bags” in bold English text cut through the front wall. Use smooth surfaces, rounded edges, a flat base, and ensure it prints without supports.
Anonymous1776511117
Create a precise, 3D-printable tea bag dispenser with exactly two parts: a main body and a removable lid. The body must hold at least 20 standard rectangular tea bags (about 65×55 mm), stacked vertically in a single column. The interior should be narrow (about 68–70 mm wide) with smooth walls and slight taper or guide rails to keep tea bags upright, aligned, and stable so they do not tip or shift. Include a gravity-fed front dispensing slot (about 5–7 mm tall) that allows only one tea bag to be pulled out at a time. Add an internal lip above the slot to stop multiple bags from coming out. The lid must use a snug friction or snap fit but remain removable. On the front, include bold uppercase English text “Tea Bags” cut fully through the wall. Use 2–3 mm wall thickness, a flat stable base, rounded edges, and support-free geometry.
Anonymous1776511117
Create a clean, functional 3D model of a compact tea bag dispenser designed for easy 3D printing. The model must have two separate parts: a main body and a removable lid. The body should hold at least 20 standard rectangular tea bags, keeping them upright, evenly aligned, and stable using simple internal guides or slightly tapered walls to prevent shifting or tipping. Include a gravity-fed dispensing opening at the bottom or front that reliably releases only one tea bag at a time without jamming or allowing multiple bags to fall out. Keep the opening simple and precise. The lid should fit snugly using a friction or snap fit, secure during use but easy to remove for refilling. Add the text “Tea Bags” engraved on the front, cut fully through the wall while maintaining structural strength. Use simple shapes, smooth surfaces, rounded edges, and a flat, stable base. Avoid complex details and ensure the model is support-free and easy to print with proper tolerances.
Anonymous1776511117
Anonymous1776502698
Anonymous1772276342
Anonymous1776481170
erstelle mir einen Kondomspender als quadratisches objekt mit hohlraum innen
Anonymous1774969794
Anonymous1776169447
Enter invite code to get credits!