?

Esp32 3D Models

Find the best Esp32 3D Models, free download in STL, FBX, GLB, OBJ, 3MF, USDZ for 3D modeling and creation in Blender, 3D printing, game developing, animation, eCommerce, AR/VR and etc. Generated by Tripo AI 3D Generator.

You May Also Like :
esp32-development-boardesp32-camesp8266microcontroller
Create a beautiful 3D-printable desk stand enclosure for a Waveshare ESP32-C6-LCD-1.69 board. Goal: Design a premium small desktop companion housing that sits on a desk and displays the screen at a nice viewing angle. It should look clean, modern, cute, and high quality, like a tiny smart assistant device. Fit requirements: - The real board size is 37.12 mm wide × 30.00 mm tall - Make the internal fit 1.00 mm larger overall than the real board size: - Internal pocket width: 38.12 mm - Internal pocket height: 31.00 mm - The board must fit snugly but safely, with realistic 3D print tolerance - Add internal rails, support lips, or snap tabs so the board stays secure without wobbling - Internal depth should fit the board and tallest components with about 1.0 mm extra clearance - Wall thickness: 2.0 to 2.5 mm Front design: - Keep the screen fully visible from the front - Add a clean, rounded screen bezel - Make the front look sleek and premium, like a tiny desktop gadget - Keep the d
Anonymous1770413084
A high-end, minimalist electronic enclosure for the ESP32-S3 but only the casing not the device itself. The design is "Quiet Luxury" tech aesthetic: a seamless, matte obsidian black finish with soft rounded corners. The top lid is perfectly flush, held by four black stainless steel hex screws. A single, tiny, diffused white LED pinhole is visible on the front. On the side, a perfectly centered USB-C port and a precision-milled gold SMA antenna connector. The "SENTRY" logo is subtly laser-etched into the top surface in a clean, modern sans-serif font. The device sits on four tiny, integrated silicone feet. The overall look is professional, expensive, and looks like high-end boutique audio or security hardware.
Anonymous1776884205
Seeed Studio Xiao ESP32-C3加0.96寸OLED显示屏的3D打印外壳，上下盖卡扣式结构，整体外尺寸32×32×14mm，壁厚2mm，所有圆角R2mm。上盖开26×26mm屏幕窗口，侧面开9×5mm Type-C口，四角做卡扣固定，无需螺丝，无悬空结构，适合Bambu A1 mini打印。
Anonymous1776844314
a case with a lid that is open in the middle for a 2.4lcd display, in the case a esp32-u needs to be able to fit with a hole for the esp32-u antenna and a boxy look that fits in your hand
Anonymous1776460693
a case with a lid that is open in the middle for a 2.4lcd display, in the case a esp32-u needs to be able to fit with a hole for the esp32-u antenna
Anonymous1776460693
a case for my esp32-u with a hole for the antenna and a lid with a part where i can put my 2,4lcd screen to fit on the lid and needs a boor fit for the things
Anonymous1776460693
Anonymous1744720000
Step 1: Define Your Nets (Power Rails): Create distinct power lines for 5V and 3.3V. Since the ESP32 and LoRa SX1278 operate at 3.3V, ensure they are connected to a regulated 3.3V source to prevent damage. Step 2: Establish the SPI Bus for LoRa: Connect the LoRa SX1278 to the ESP32 using the SPI protocol pins: SCK (GPIO18), MISO (GPIO19), MOSI (GPIO23), and NSS/CS (GPIO5). Step 3: Connect Sensors and GPS: Ultrasonic Sensor: Connect the Trigger and Echo pins to the ESP32. Use a voltage divider on the Echo pin to step down the 5V signal to 3.3V for the ESP32’s safety. GPS Module: Connect the TX/RX pins to the ESP32’s hardware serial pins (GPIO16/17). Step 4: Add Protection and Decoupling: Place 0.1µF and 10µF decoupling capacitors near the power pins of the ESP32 and LoRa module to filter out electrical noise and stabilize signals.
Anonymous1775101996
Anonymous1775902093
Create a compact 3D‑printable enclosure for a Waveshare 1.5'' OLED 128×128 display and an ESP32‑C3 SuperMini. Include a precise front window for the OLED with a thin bezel, internal standoffs for both boards, and space for short jumper wires. Use ~2 mm walls and FDM‑friendly geometry with no extreme overhangs. Add a snap‑fit removable back cover On the rear, add four 3 mm mounting holes in a rectangular pattern for attaching the enclosure to a server/NAS case. Keep the exterior minimal, smooth, and appliance‑grade, and keep the enclosure as small as possible while maintaining safe internal clearances and fully manifold geometry.
Anonymous1775860822
Pls generate model for attendance system box which will contain esp32, pcb board double sided 12*9 and all the other components inside the box.
Anonymous1775761117
crea una caja rectangular para que su unterior instale una tarjeta esp32 con una abertura para el conector usb, tambien llevara una pantalla oled 0.96" y un sensor de temperatura dht22
carlosml85
necesito una caja para integrear un tarjeta esp32, una pantalla oled 0.96" y un sensor de temperatura dht22
carlosml85
ESP32 s3 n16r8
Anonymous1775477853
Anonymous1765319682
Anonymous1775416668
aerial screw but add motors and it runs on esp32c
Anonymous1775293875
عندي 7 حساسات مستشعر ثاني اكسيد كربون و وحدة ساعةRTC Winsen ZCE04B 4-in وحدة بطاقة مايكرو إس دي لوحة تطوير ESP32 استشعار درجة الحرارة ابغا تصميم يجمع الحساسات فقط على شكل هرمي أو برج 3d
Anonymous1775236325
Enter invite code to get credits!