Esp32 3D Models

Find the best Esp32 3D Models, free download in STL, FBX, GLB, OBJ, 3MF, USDZ for 3D modeling and creation in Blender, 3D printing, game developing, animation, eCommerce, AR/VR and etc. Generated by Tripo AI 3D Generator.

You May Also Like :

Anonymous1763568795

Anonymous1762281743

a case with a lid that is open in the middle for a 2.4lcd display,
in the case a esp32-u needs to be able to fit with a hole for the esp32-u antenna and a boxy look that fits in your hand

Anonymous1776460693

a case with a lid that is open in the middle for a 2.4lcd display,
in the case a esp32-u needs to be able to fit with a hole for the esp32-u antenna

Anonymous1776460693

a case for my esp32-u with a hole for the antenna and a lid with a part where i can put my 2,4lcd screen to fit on the lid and needs a boor fit for the things

Anonymous1776460693

Create a compact 3D‑printable enclosure for a Waveshare 1.5'' OLED 128×128 display and an ESP32‑C3 SuperMini. Include a precise front window for the OLED with a thin bezel, internal standoffs for both boards, and space for short jumper wires. Use ~2 mm walls and FDM‑friendly geometry with no extreme overhangs. Add a snap‑fit removable back cover On the rear, add four 3 mm mounting holes in a rectangular pattern for attaching the enclosure to a server/NAS case. Keep the exterior minimal, smooth, and appliance‑grade, and keep the enclosure as small as possible while maintaining safe internal clearances and fully manifold geometry.

Anonymous1775860822

Anonymous1757426804

Anonymous1757316867

Generate me a UFO that has enough space inside for a breadboard and electronics. The breadboard is standard size. However, there should be enough space to accommodate the electronics on the breadboard and an ESP32 controller.

Anonymous1756474392

Anonymous1756432088

两块电路板ESP32和MPU6050，ESP32尺寸 51.5*28.2*1.5，MPU6050尺寸20*16*1.7，需要长宽高尽可能小，里面有滑槽来固定电路板，需要放置CR1632纽扣电池。需要有缠过手胶的羽毛球拍拍柄末端的纹路，且mpu6050传感器（图片中较小的那个）需要是有电子元件的一面水平向上。这两个传感器需要基本固定。ESP32与mpu6050垂直拜访，mpu6050放在ESP32的两排针脚中间。建模时不需要建出这两个传感器只需要给他们留出空间拜访。纽扣电池有电池扣，也需要留出空间给它摆放。需要是滑动门，打开门有放置ESP32与mpu6050与纽扣电池及其电池扣的卡槽，滑动门很明显需要有滑槽，滑动门希望是磁吸的（如果可以的话）。ESP32竖直摆放（即正面有电子元件的一面竖直），mpu6050正面即有电子元器件的一面水平向上。记得稍微留出一些线的空间。我需要你制作一个外壳给我放置我的传感器。

Anonymous1755837059

两块电路板ESP32和MPU6050，ESP32尺寸 51.5*28.2*1.5，MPU6050尺寸20*16*1.7，需要长宽高尽可能小，里面有滑槽来固定电路板，需要放置CR1632纽扣电池。做成圆柱形，需要有缠过手胶的羽毛球拍拍柄末端的纹路，且mpu6050传感器（图片中较小的那个）需要是有电子元件的一面水平向上。这两个传感器需要基本固定。

Anonymous1755837059

Anonymous1755671475

Anonymous1753116750

Design a mount for an ESP32 development board, sized approximately 58mm x 25mm, with two M2.5 or M3 mounting holes spaced according to the official ESP32 dev board layout. The mount should attach securely to the chassis using M3 bolts and nut slots (6mm hex, 2.5mm deep). Leave space for USB access and allow for cable routing. Optimize for 3D printing.

Anonymous1753058253