?

Flat panel 3D Models

Find the best Flat panel 3D Models, free download in STL, FBX, GLB, OBJ, 3MF, USDZ for 3D modeling and creation in Blender, 3D printing, game developing, animation, eCommerce, AR/VR and etc. Generated by Tripo AI 3D Generator.

You May Also Like :

paneled-sides square-panel panel flat-screen

Anonymous1738447528

Anonymous1756070041

Anonymous1762324954

Anonymous1740365756

Anonymous1754916484

将这张扁平的2D插图转换为3D模型，保证结构的物理连接合理

Anonymous1762403736

Anonymous1749013595

将这张扁平的2D插图转换为3D风格图像，仅建出红色线条框内的木制栏杆，保留细节，棱角分明，移除栏杆后八棱八面的旋转柜，图片需要精致。

Anonymous1758712695

Anonymous1739539979

Anonymous1760600377

Anonymous1759223077

Anonymous1759242104

Create one connected object composed of three required elements: a C-channel, a cylindrical hinge, and a flat panel with a rounded lower edge. These three elements must form one continuous printable part. Do not omit, duplicate, or stylize.

Panel (primary element):

The panel is flat and planar, not curved or domed.

Shape: the top edge is straight and horizontal, while the bottom edge is a smooth semicircular arc, so the outline looks like a rectangle with its lower half replaced by a half-circle.

Overall dimensions: width left-to-right ≈ 95 mm; maximum height at the center ≈ 64 mm.

Thickness (front-to-back depth): ≈ 2.5 mm across the full area.

Surfaces must be plain, smooth, and featureless, with softly rounded (filleted) outer edges.

Optionally add a lip ridge along the top edge, where the panel meets the clip and hinge: ridge ≈ 2 mm tall × 2 mm wide, continuous along that edge, to block light leakage.

The panel must exist only once — no duplication, no stacking, no secondary plates.

Hinge (secondary element):

A plain cylindrical pivot axis that connects the clip to the panel.

Cylinder diameter ≈ 3.5 mm.

Axis runs parallel to the panel’s width (the long 95 mm edge).

The hinge is a simple smooth cylinder, no gears, no teeth, no springs, no knuckles.

Placement: centered vertically on the rear/top edge of the panel, joining panel to the outer side of the C-channel.

C-channel Clip (support element):

A slim rectangular C-shaped channel sized to fit over a cap brim.

Length along panel edge: ≈ 26 mm.

Depth front-to-back: ≈ 12 mm.

Internal slot gap in vertical dimension strictly ≈ 3–6 mm (narrow).

Two parallel jaws form this slot; each jaw ≈ 2–3 mm thick.

Inside faces of both jaws must contain shallow grip ribs: 2–3 ribs per jaw, rounded, each ≈ 0.5–0.8 mm tall and ≈ 1 mm wide, oriented lengthwise. These provide friction without sharp teeth or fabric damage.

Exterior surfaces plain, smooth, no cutouts, no textures, no decorative details.

Overall constraints:

The object must be one manifold: clip, hinge, and panel all fused.

Bilaterally symmetrical about a vertical midplane so the part can be flipped left-to-right for reversible use.

The hinge must clearly connect the clip to the panel, not float or separate.

Style: minimalist, utilitarian, printable engineering part.

Absolutely no duplication of panels, no ornamental features, no decorative holes, and no dome-like curves.

The result should appear as a slim, flat, rounded-bottom shield panel attached by a small cylindrical hinge to a narrow ribbed C-channel clip sized for a standard brim (3–6 mm).

Anonymous1759508085

Create one connected object composed of three required elements: a C-channel, a cylindrical hinge, and a flat panel with a rounded lower edge. These three elements must form one continuous printable part. Do not omit, duplicate, or stylize.

Panel (primary element):

The panel is flat and planar, not curved or domed.

Shape: the top edge is straight and horizontal, while the bottom edge is a smooth semicircular arc, so the outline looks like a rectangle with its lower half replaced by a half-circle.

Overall dimensions: width left-to-right ≈ 95 mm; maximum height at the center ≈ 64 mm.

Thickness (front-to-back depth): ≈ 2.5 mm across the full area.

Surfaces must be plain, smooth, and featureless, with softly rounded (filleted) outer edges.

Optionally add a lip ridge along the top edge, where the panel meets the clip and hinge: ridge ≈ 2 mm tall × 2 mm wide, continuous along that edge, to block light leakage.

The panel must exist only once — no duplication, no stacking, no secondary plates.

Hinge (secondary element):

A plain cylindrical pivot axis that connects the clip to the panel.

Cylinder diameter ≈ 3.5 mm.

Axis runs parallel to the panel’s width (the long 95 mm edge).

The hinge is a simple smooth cylinder, no gears, no teeth, no springs, no knuckles.

Placement: centered vertically on the rear/top edge of the panel, joining panel to the outer side of the C-channel.

C-channel Clip (support element):

A slim rectangular C-shaped channel sized to fit over a cap brim.

Length along panel edge: ≈ 26 mm.

Depth front-to-back: ≈ 12 mm.

Internal slot gap in vertical dimension strictly ≈ 3–6 mm (narrow).

Two parallel jaws form this slot; each jaw ≈ 2–3 mm thick.

Inside faces of both jaws must contain shallow grip ribs: 2–3 ribs per jaw, rounded, each ≈ 0.5–0.8 mm tall and ≈ 1 mm wide, oriented lengthwise. These provide friction without sharp teeth or fabric damage.

Exterior surfaces plain, smooth, no cutouts, no textures, no decorative details.

Overall constraints:

The object must be one manifold: clip, hinge, and panel all fused.

Bilaterally symmetrical about a vertical midplane so the part can be flipped left-to-right for reversible use.

The hinge must clearly connect the clip to the panel, not float or separate.

Style: minimalist, utilitarian, printable engineering part.

Absolutely no duplication of panels, no ornamental features, no decorative holes, and no dome-like curves.

The result should appear as a slim, flat, rounded-bottom shield panel attached by a small cylindrical hinge to a narrow ribbed C-channel clip sized for a standard brim (3–6 mm).

Anonymous1759508085

Anonymous1752492084

Anonymous1737276602

Anonymous1756113871

Anonymous1767708420