Hinged lid 3D Models

Find the best Hinged lid 3D Models, free download in STL, FBX, GLB, OBJ, 3MF, USDZ for 3D modeling and creation in Blender, 3D printing, game developing, animation, eCommerce, AR/VR and etc. Generated by Tripo AI 3D Generator.

You May Also Like :

Anonymous1763619825

Anonymous1763710227

BOB

Anonymous1746635356

wozdac

Porta blindata, stile militare, costruita con scarti di metallo

Anonymous1761441072

Pointzero_masterACC

Anonymous1760691982

Anonymous1749794841

Anonymous1760508469

Anonymous1743040202

Create one connected object composed of three required elements: a C-channel, a cylindrical hinge, and a flat panel with a rounded lower edge. These three elements must form one continuous printable part. Do not omit, duplicate, or stylize.

Panel (primary element):

The panel is flat and planar, not curved or domed.

Shape: the top edge is straight and horizontal, while the bottom edge is a smooth semicircular arc, so the outline looks like a rectangle with its lower half replaced by a half-circle.

Overall dimensions: width left-to-right ≈ 95 mm; maximum height at the center ≈ 64 mm.

Thickness (front-to-back depth): ≈ 2.5 mm across the full area.

Surfaces must be plain, smooth, and featureless, with softly rounded (filleted) outer edges.

Optionally add a lip ridge along the top edge, where the panel meets the clip and hinge: ridge ≈ 2 mm tall × 2 mm wide, continuous along that edge, to block light leakage.

The panel must exist only once — no duplication, no stacking, no secondary plates.

Hinge (secondary element):

A plain cylindrical pivot axis that connects the clip to the panel.

Cylinder diameter ≈ 3.5 mm.

Axis runs parallel to the panel’s width (the long 95 mm edge).

The hinge is a simple smooth cylinder, no gears, no teeth, no springs, no knuckles.

Placement: centered vertically on the rear/top edge of the panel, joining panel to the outer side of the C-channel.

C-channel Clip (support element):

A slim rectangular C-shaped channel sized to fit over a cap brim.

Length along panel edge: ≈ 26 mm.

Depth front-to-back: ≈ 12 mm.

Internal slot gap in vertical dimension strictly ≈ 3–6 mm (narrow).

Two parallel jaws form this slot; each jaw ≈ 2–3 mm thick.

Inside faces of both jaws must contain shallow grip ribs: 2–3 ribs per jaw, rounded, each ≈ 0.5–0.8 mm tall and ≈ 1 mm wide, oriented lengthwise. These provide friction without sharp teeth or fabric damage.

Exterior surfaces plain, smooth, no cutouts, no textures, no decorative details.

Overall constraints:

The object must be one manifold: clip, hinge, and panel all fused.

Bilaterally symmetrical about a vertical midplane so the part can be flipped left-to-right for reversible use.

The hinge must clearly connect the clip to the panel, not float or separate.

Style: minimalist, utilitarian, printable engineering part.

Absolutely no duplication of panels, no ornamental features, no decorative holes, and no dome-like curves.

The result should appear as a slim, flat, rounded-bottom shield panel attached by a small cylindrical hinge to a narrow ribbed C-channel clip sized for a standard brim (3–6 mm).

Anonymous1759508085

Create one minimalist, functional clip-on blinder designed for a baseball cap brim. It must be a single reversible part, not decorative. The design is composed of three clear elements: clip, hinge, and shade panel. All three must be included as one connected geometry. Do not omit any of these parts.

Shade Panel (primary feature):

The panel is the main element and must dominate the shape.

It is tapered, not a rectangle. This taper is mandatory.

Rear edge (temple side) height: ~64 mm.

Front edge (nose side) height: ~45 mm.

Length along brim edge: ~95 mm.

Width front-to-back: ~55–60 mm.

Thickness: ~2.5 mm.

Surfaces must be perfectly flat and smooth, not curved, not domed.

Edges should be softly rounded (filleted) for comfort and printability.

Optional lip: add a small straight ridge along the inner brim edge of the panel, ~2 mm tall x ~2 mm wide, to block light leaks.

The taper should be visible in side view as a trapezoid: tall at the back, short at the front.

Hinge (secondary feature):

A plain cylindrical friction hinge, not gears, not latches, not knuckles.

Cylinder diameter: ~3.5 mm.

Hinge axis runs parallel to the brim edge.

The hinge connects the outer side of the clip to the side of the panel.

Function: allows panel to rotate down beside the eye or fold up flat against the brim.

Must be visually obvious that the hinge joins the clip and the panel.

Clip (support feature):

A slim C-shaped clip, not bulky.

Length along brim: ~26 mm.

Depth front-to-back: ~12 mm.

Inner slot gap: 3–6 mm only (narrow).

Jaws: 2–3 mm thick each.

Inside surfaces: add 2–3 shallow ribs per jaw. Each rib ~0.5–0.8 mm tall, ~1 mm wide, running front-to-back.

These ribs increase friction on the hat brim. They must be rounded, not sharp teeth.

Outside surfaces smooth, plain, no textures, no ornament.

Overall requirements:

Geometry must be one single connected part: clip + hinge + tapered panel.

The part must be reversible: can be used left or right simply by flipping.

The overall style should be slim, utilitarian, engineering-like, printable in PETG.

No decorative textures, logos, or extra geometry.

No duplication of panels — exactly one panel.

No large dome shapes or helmet-like curves.

No gear teeth or serrations on hinge.

The result should look like a slim, tapered flat shield attached by a hinge to a narrow clip, sized correctly to snap onto a standard baseball cap brim (3–6 mm thick).

Anonymous1759508085

A minimalist clip-on cap brim blinder, single reversible part. The main feature is a flat tapered shade panel, not doubled, not curved. The panel is rectangular, about 95 mm long parallel to the brim, about 55–60 mm wide front-to-back, 64 mm tall at the rear edge, 45 mm tall at the front edge, and about 2.5 mm thick. Surfaces must be flat, smooth, and plain with softly rounded edges. From one side of this panel extends a small cylindrical hinge, about 3.5 mm diameter, running parallel to the brim edge. The hinge connects the panel to a slim C-shaped clip. The clip is about 26 mm long, 12 mm deep, with an inner slot 3–6 mm wide to grip a baseball cap brim. The clip jaws are 2–3 mm thick and smooth outside. On the inside, add 2–3 shallow rounded ribs per jaw, about 0.5–0.8 mm tall and 1 mm wide, running front-to-back to improve grip. The clip should be slim and simple, not bulky. The hinge should be plain, no gears, no textures. The geometry must appear as one connected object: clip, hinge, and panel. It should look like a slim functional engineering part, symmetrical so it can be flipped left or right.

Anonymous1759508085

A minimalist, functional clip-on blinder designed for a baseball cap brim. It is a single reversible part. The design begins with a slim C-shaped clip that slides onto the brim edge. The clip is about 26 mm long along the brim, about 12 mm deep front-to-back, with a narrow slot only 3–6 mm wide to grip the brim securely. The jaws should be 2–3 mm thick, smooth on the outside, but the inside should have shallow ribs for friction. Add 2–3 rounded ridges per jaw, each 0.5–0.8 mm high and about 1 mm wide, running front-to-back. These ribs improve grip on fabric without cutting or damaging the hat. From the outer face of the clip extends a simple cylindrical friction hinge, about 3.5 mm in diameter, running parallel to the brim edge. This hinge must be plain and functional, not gears, not a latch. Attached to this hinge is exactly one flat tapered panel, not curved, not domed, not doubled. The panel is about 95 mm long parallel to the brim, about 64 mm tall at the rear, 45 mm tall at the front, about 55–60 mm wide front-to-back, and about 2.5 mm thick. The panel surfaces must be flat and smooth with softly rounded edges. Optionally add a small lip, 2 mm tall and 2 mm wide, along the edge nearest the brim to block light. The part must be symmetrical, plain, and printable so it can be flipped and used on either side of the hat.

Anonymous1759508085

Jonathan Kobylasnki

Anonymous1725624219