?

Rectangular prism 3D Models

Find the best Rectangular prism 3D Models, free download in STL, FBX, GLB, OBJ, 3MF, USDZ for 3D modeling and creation in Blender, 3D printing, game developing, animation, eCommerce, AR/VR and etc. Generated by Tripo AI 3D Generator.

You May Also Like :
wide-anglesquare-blurhigh-angleprism
Anonymous1775191255
Can you make me a rectangular prism with 2 sections one section is a cup holder and the other section is to put snacks in and at the bottom can you make a slight opening where I can put an ice pack under the cup section and can you add a clamp to one side so it can clamp to a table
Anonymous1776628871
Anonymous1774940192
A single, solid rectangular prism block. The top face and all sides are flat. The entire base surface seamlessly transitions into a continuous, sculpted smooth sinusoidal wave profile across its length. The entire object is a single, solid piece of material with no interior voids. Clean matte finish.
Anonymous1770366661
sacarle base al modelo, que solo sea la parte blanca y hueca
Anonymous1776290332
Anonymous1774573483
帮我设计一个 宽1.8CM,长5.8cm，厚0.2cm的长方形的3D模型
Anonymous1776168793
白色中空长方体，长 20cm，宽 10cm，高 4cm，壁厚 1.5mm。 上表面中心区域均匀分布 4 个正方形凹槽，凹槽边长 0.8cm，深度 0.5cm。 凹槽位置：距离长边边缘 3cm，距离短边边缘 4cm。 左右两侧面中心各有 2 个圆形通孔，孔径 0.6cm，孔距 4cm，距离上下边缘各 1.5cm。 两端端面各有一个小型环形凸起，用于悬挂链条。 整体密封中空，轻量化结构
Anonymous1773658866
A small, solid plastic component shaped like a truncated rectangular prism (frustum). The base geometry is square, with slightly tapered side faces. 📏 Dimensions Bottom face (base): 20 mm × 20 mm Top face: 18 mm × 18 mm Total height: 15 mm 📐 Geometry The side faces slope evenly from the larger bottom face to the smaller top face. The taper is symmetrical on all four sides (uniform inward slope). Each side face is a flat, slightly inclined plane (no curvature). 🔲 Edges All edges are slightly rounded or chamfered Radius approx. 0.5–1 mm No sharp 90° edges 🎨 Surface / Material Appearance: black plastic Finish: matte to satin (semi-matte) Surface is mostly smooth, with fine scratches / micro-wear marks 🔽 Bottom Side (Base) Flat overall, but with a shallow rectangular recess in the center Inside the recess: small circular marks (likely ejector pin marks from manufacturing) A slightly raised rim runs around the outer edge 🔼 Top Side Flat and clean No recess or markings Smaller
Anonymous1775992977
parking lot concrete divider
Anonymous1775925314
Anonymous1775934146
Positive Prompt: A solid rectangular block. No holes, no hollow. Shape like a domino tile: rectangle with rounded corners and rounded edges. Thick and chunky. Clean, sharp geometry. One piece. Negative Prompt: hollow, hole, cavity, empty, soft, melted, blobby, smooth, organic, low poly, faceted, plastic, glossy, shiny, metal, wood, texture, dots, pips, spots
Anonymous1775932949
треугольная призма с катетами 35 мм и 50 мм длиной 140 мм
Anonymous1775893740
I need a rectangle that is 3.25" long x 4.25" high with a thickness of 0.20" with a rectangle slit style opening on one of the 3.25" sides that allows me to insert something that is 3" wide x 4" tall x 0.035" thick
Anonymous1747708468
mam otwór prostokątny o wymiarach 19,5 x15 i grubości 1,5mm i wygeneruj mi do niego zaślepkę
Anonymous1771274305
Прямоугольная бронеплита размерами ширина 24 см, высота 32 см, толщина ровно 15 мм. Вся модель состоит из гироидной решётки (трёхмерная периодическая поверхность минимальной энергии). Гироид образован непрерывной сетью гладких винтообразных каналов, ячейки открытые, сквозные. Структура должна обеспечивать максимальную продуваемость воздуха (высокую пористость) и превосходное рассеивание энергии при ударной или взрывной нагрузке (запреградное воздействие). Геометрия чёткая, инженерная, без самопересечений. Белый студийный свет, нейтральный фон.
Anonymous1775132777
A modular 3D logo composed of a rectangular prism base with beveled edges, featuring a large extruded green ‘T’ on the front face, a vertical dark blue rectangular insert, vertical side texts (‘INNOVA’ in green and ‘3D LAB’ in dark blue), and angular triangular decorative elements. Each component should be a separate mesh for easy manipulation and assembly. Clean geometric style, isometric perspective.”
Anonymous1774362934
Anonymous1774853745
Enter invite code to get credits!