3D Workspace
Home
Assets
Affiliate Program
Sign up/Log in
?
Upgrade
DCC Bridge
Anonymous1764045834
11-25 04:52
Model Name
pink robot toy 3d model
Tags
machine
machine rendering
machine rendering stylized
machine stylized
pink robot toy
rendering
rendering stylized
stylized
toy
Input
Prompt
Create a 3D model of the front half of a cute kawaii-style bird-shaped electronic device enclosure. The first image shows an idea of the full product design (you must generate just one part as described bellow). OVERALL SHAPE: - Rounded oval/egg shape, wider in the middle, narrower at top and bottom - Smooth, organic curves (like a cute chubby bird body) - Height: 180mm, Width: 120mm (at widest point), Depth: 45mm - Wall thickness: 3mm minimum throughout - Soft, rounded edges everywhere (no sharp corners) - Style: Cute, friendly, child-appealing aesthetic DETAILED FEATURES (from top to bottom): TOP SECTION (150-180mm height): - Two small circular holes for proximity sensor at 145mm height from base * Diameter: 4mm each * Spacing: 24mm between centers (horizontal alignment) * Positioned centrally on the face - Internal rectangular cavity behind these holes: 22mm wide x 8mm tall x 5mm deep UPPER-MIDDLE SECTION (100-150mm height): - Two large circular holes for decorative 3D eyes at 125mm height from base * Front hole diameter: 20.5mm each (goes through front wall) * Spacing: 40mm between centers (horizontal alignment) * Internal cavity behind each eye: 28mm diameter x 20mm deep * These cavities are for mounting the eye components from behind MIDDLE SECTION (40-100mm height): - Circular area at 105mm height for beak attachment (35mm diameter) * This is a flat mounting surface, NOT a hole * Four small raised posts (1.5mm tall, 3mm wide) positioned around this area at 90° intervals * Behind this area: large circular cavity 52mm diameter x 28mm deep for speaker LOWER-MIDDLE SECTION (40-100mm height): - Large rectangular cutout for display screen, centered at 75mm from base * Outer cutout: 62mm wide x 49mm tall * Rounded corners with 3mm radius * Goes completely through the front wall - LED channel surrounding the screen cutout: * Channel width: 8mm * Channel depth: 5mm * Runs all around the screen cutout (complete rectangle) * Inner corners: 5mm radius, Outer corners: 8mm radius * Top edge of channel has 1mm deep groove (8mm wide) for snap-fit cover - Internal rectangular recess behind screen: * Size: 84mm wide x 52mm tall x 7mm deep * For mounting the actual display PCB * Positioned around the screen cutout SIDE SECTIONS (70-100mm height): - Four square holes for buttons on the sides: * Left side: 2 holes (upper at 95mm, lower at 75mm from base) * Right side: 2 holes (upper at 95mm, lower at 75mm from base) * Each hole: 13mm x 13mm * 10mm from the outer edge * Internal cavity behind each: 15mm x 15mm x 10mm deep RIGHT SIDE INTERNAL (85mm height): - Internal cavity for reed switch (not visible from outside): * Position: 15mm from outer surface, 85mm from base * Size: 30mm long x 16mm wide x 10mm deep * Small 3mm wide channel running from this cavity downward for wires BOTTOM SECTION (0-40mm height): - Two mounting points for feet at the base: * Position: 60mm apart (center to center) * Each mounting point: 8.2mm diameter hole, 12mm deep * Or alternatively: 20mm x 15mm flat surface area for gluing * Reinforced area around each mounting point (extra 3mm thickness) - Small bumper mounting positions (optional): * Four small 1mm deep recesses, 10mm diameter * For silicone bumper pads * Two near each foot position ASSEMBLY FEATURES: - Perimeter flange for joining with back half: * 5mm wide flat surface all around the opening edge * 6-8 mounting holes (3.2mm diameter, 15mm deep) distributed around perimeter * 2mm deep countersink (6mm diameter) at each mounting hole - Four alignment pins: * 4mm diameter x 8mm tall * Located at corners/key positions * To ensure perfect alignment with back half INTERNAL FEATURES: - Smooth internal surfaces - No sharp internal edges - Support ribs if needed for structural strength (1-2mm thick) - All cavities and recesses properly connected to main hollow body CRITICAL REQUIREMENTS: - All holes must go through appropriate walls completely where specified - All cavities must be accessible from inside - Wall thickness never less than 3mm - No undercuts that would prevent 3D printing - Smooth transitions between all surfaces - Printable without supports on major surfaces (orient for printing with front face UP) STYLE NOTES: - Organic, flowing curves (like a real bird but simplified/stylized) - Friendly and approachable appearance - Clean, modern aesthetic - Child-safe design (no sharp edges anywhere) - Should look like a cute character, not industrial OUTPUT FORMAT: - Clean mesh topology - Manifold (watertight) geometry - Appropriate polygon count for 3D printing - Units in millimeters - Origin at bottom center of the model
Detailed Info
Related Models
Enter invite code
Enter invite code to get credits!
Anonymous1764045834
Anonymous1764045834