3D Workspace
Home
Assets
Affiliate Program
Creator Program
Sign up/Log in
View Plans
DCC Bridge
kingnoob63026
11-27 05:10
Model Name
leather backpack 3d model
Tags
bag
leather
leather backpack
props
props realistic
props rendering
props rendering realistic
realistic
rendering
rendering realistic
Prompt
Overall proportions: The backpack is taller than it is wide. Height is about 1.5 times the width. Depth is about half the width. The overall shape is a soft rectangular box with slightly rounded edges and corners. It stands upright on a flat bottom. All surfaces are made of worn medium-brown leather with visible stitching along every edge. All hardware is aged brass. There are no zippers, no plastic parts, no metal rails, no metal frames. Front side: The front of the backpack has a large triangular flap at the top. This flap is wide, covering almost the full width of the bag, and forms a shallow upside-down “V” shape where the two sides meet in the center. In the middle of this flap, slightly above the center, there is a brass sheriff star badge mounted on a round brass plate. The star has five points with small round studs at the tip of each point and a smaller star or emblem in the middle. Under the badge, a single vertical leather strap comes down from the flap. This strap passes through a small rectangular brass buckle on the front of the bag and continues downwards. It is the main closing strap of the flap. Below the flap, on the lower front of the backpack, there is one large front pocket. This pocket is almost as wide as the bag, and about one third of the bag’s height. It has its own rounded flap with soft corners, and on the center of that flap there is another vertical leather strap with a small brass buckle. This front pocket is boxy and sticks out a little from the main body, with visible side walls and stitching along all the edges. Right side: On the right side of the backpack (from the wearer’s point of view) there is a tall cylindrical leather holster attached directly to the side panel. The holster runs vertically from near the bottom of the bag to just below the top. The cylinder is closed at the bottom and open at the top. Inside the holster there is a short wooden baton or club sticking out, with only the rounded wooden handle visible above the holster. The holster is made from the same brown leather and is sewn or riveted directly to the side of the backpack in one solid piece – do not use multiple loose straps wrapped around it like a separate case. Left side: On the left side of the backpack there is a small boxy side pocket. This pocket is rectangular, with a front flap that folds down. The flap has a small leather strap or a leather tab with a brass button or stud to close it. The pocket is not huge; it should be clearly smaller than the big front pocket. Again, all edges of the pocket show stitched seams. Back side (very important): The back is a flat, rectangular leather panel. Along the left and right edges of this back panel there are subtle vertical seams or stitching lines to show that the leather is sewn to the sides. At the top center of the back there is one short, thick leather carry handle. This handle is attached close to the top edge with two small rectangular leather patches and brass rivets. It lies horizontally, but it should be small and clearly just a handle, not a large strap system. Below the handle, there are two wide, padded shoulder straps. These are the most important detail: – The straps are attached high on the back, near the left and right upper corners, using small rectangular leather patches with brass rivets. – Each strap is about as wide as two adult fingers, and looks padded, with a slightly rounded surface and visible stitching all along its edges. – The straps curve naturally downward following the shape of a real backpack strap, then go toward the bottom corners. – At the lower corners of the back, each strap connects to a brass D-ring or simple rectangular brass ring that is attached to a triangular leather tab sewn to the bottom corner of the bag. There should be no wide horizontal strap going across the back panel, no belt-like closure across the back. The only elements on the back panel are the small top handle fixed near the top, the two shoulder straps, and the stitching along the edges. Bottom: The bottom of the backpack is a simple rectangle of leather with slightly rounded corners and visible stitching all around. It is thick and flat so the backpack can stand upright. No metal feet, no plastic parts. Lawman theme: This backpack clearly belongs to a lawman / sheriff. The sheriff star on the front flap and the baton holster on the side make this obvious. The design is practical and robust, not fancy. It should look like field gear for a law officer riding in the Old West. Style and rendering: The style is realistic, like a high-quality game asset from Red Dead Redemption 2. The leather is worn but not destroyed, with soft highlights and darker creases. The brass is slightly tarnished. No modern e
Detailed Info
Related Models
Enter invite code
Enter invite code to get credits!
kingnoob63026
kingnoob63026kingnoob63026