18mm 3D Models

Find the best 18mm 3D Models, free download in STL, FBX, GLB, OBJ, 3MF, USDZ for 3D modeling and creation in Blender, 3D printing, game developing, animation, eCommerce, AR/VR and etc. Generated by Tripo AI 3D Generator.

You May Also Like :

egy tömör alumínium hasábot szeretnék. 80 mm x 15 mm x 2400 mm méretben. A 80 mm-es oldalán az egyik végétől 850 mm-re legyen rajta egy ovális kimarás, aminek a mérete 500 mm x 30 mm. A kimarásnál az egyik oldalon 20 mm alu, a másik oldalon 30 mm maradjon meg. Az ovális kimarás élei körben legyenek lekerekítve (2 mm-es rádiuszra). Ahol a 80 mm-es oldalon megmaradt a 30 mm anyag, azok az élek is legyenek lekerekítve ugyanúgy 2mm rádiuszra.

Emmaph

Gabarito P/ Ajustar Arremate Fechamento Chapas 15 E 18mm

Anonymous1769290712

Anonymous1769188512

Smooth 18mm-thick and width 500mm and height 650mm

Anonymous1769188512

its precise 3mm height and 32mm length markings

Anonymous1768759201

ABS塑料盖三维工程图，正圆柱体，外径47mm总高18mm，顶板厚2mm实心，侧壁厚3mm高16mm，内侧内腔直径41mm深16mm；侧壁内侧2条半圆柱引导柱，180度对称，半径1.3mm长16mm，平面贴侧壁内侧、弧面朝内腔中心，顶端接顶板内表面、底端和侧壁开口平齐，带剖视图+立体视角，线条清晰标全尺寸，工业设计风

Anonymous1768668273

25mm cylinder 32mm long step down to a 20mm cylinder 18mm long

Anonymous1768588194

faz um anel igual esse modelo , como o diametro do aro interno de 18 mm

Anonymous1768488601

底下键帽规格：采用通用 SA R1（或OEM）高度键帽为基准。总高度约 18-20mm，顶部投影面积 18mm×18mm（兼容标准间距）。此为艺术创作的“画布”。
• 底部结构：必须包含精确的 Cherry MX十字柱接口（内径约4mm，深约3.5-4mm），以及用于增强强度的内壁加强筋（ribs）。这是功能性的基石。

Anonymous1762755964

键帽规格：采用通用 SA R1（或OEM）高度键帽为基准。总高度约 18-20mm，顶部投影面积 18mm×18mm（兼容标准间距）。此为艺术创作的“画布”。
• 底部结构：必须包含精确的 Cherry MX十字柱接口（内径约4mm，深约3.5-4mm），以及用于增强强度的内壁加强筋（ribs）。这是功能性的基石。

Anonymous1762755964

genera este modelo que sea simetrico y la parte de adentro sea en forma de rosca, que mida 18mm de diametro y 10 mm de altura

danieldeniciam

A rectangular slab of hard tool plastic or aluminum. Its overall dimensions are 222mm in length, 152mm in width, and 20mm in thickness. (Note: 因为图纸比例为1:2，所以实际尺寸111x76x10需乘以2输入，以生成合适大小的模型供缩放)。

On the top face, there is a large rectangular recess. This recess is centered on the slab. The recess has a length of 180mm, a width of 112mm, and a depth of 14mm. (对应图纸顶部7.0深槽，尺寸90x56x7，放大2倍)。

The slab has four through holes for mounting, located near each corner. These holes have a diameter of 6mm (对应图纸3.00孔径，放大2倍)。 The edges of the entire slab are slightly rounded (broken edges), not sharp.

Engineering drawing style, solid, no textures, white background, isometric view.A single, small rectangular protrusion or block, made of hard plastic. Its top dimensions are 18mm in length and 9mm in width (对应图纸9.00 x 4.50 TYP，放大2倍)。 The vertical sides have a draft angle, meaning the base is slightly larger than the top. The height of the block is 6mm (对应图纸3.00高度，放大2倍)。 All four vertical edges of the top are rounded with a small

Anonymous1745809963

Can you generate 3d model of an auger. I want it to be 12cm long, diameter of 48mm, pitch 2.5cm, shaft diameter 18mm. At one end of the auger is a flanged coupling with the flanged thickness of 3mm, the flanged diameter is 30mm and make a notch on the middle of the flanged

Anonymous1760442294

Solid cylinder, outer diameter 47mm, total height 18mm; top plate 2mm thick solid full circle; side wall 3mm thick, height 16mm, inner cavity diameter 41mm, depth 16mm; 2 symmetrical semi-cylindrical guide posts attached to inner cavity wall, radius 1.3mm, length 16mm, same height as inner cavity

Anonymous1768668273

18mm test tube adapter to 1/2 inch test tube.

Anonymous1752280770

i have 300mm circle mold. i need 3mm reinforcement around, but my printer can only print 200mmX200mm so it needs to be from multiple connecting parts. height of 18mm. i need simple circle divided to 4 parts with ears so i can clamp them

Anonymous1771584522

Anonymous1767620318

this 3D wall panel engraving design made on 18mm thickness HDHMR board, turn this into 18 mm engraved 3d model of wall panel of size : 8 feet by 6 feet

Anonymous1757669211