7mm 3D Models

Find the best 7mm 3D Models, free download in STL, FBX, GLB, OBJ, 3MF, USDZ for 3D modeling and creation in Blender, 3D printing, game developing, animation, eCommerce, AR/VR and etc. Generated by Tripo AI 3D Generator.

You May Also Like :

Anonymous1775833183

i want to make a 3d circle R=5cm H=1.7mm

Anonymous1774711117

Anonymous1775381812

BARRA RECTANGULAR CON LAS SIGUIENTES MEDIDAS: 0.6MM, 0.7MM, 35MM

Anonymous1772731307

Anonymous1762224465

Anonymous1771941120

원형 심볼만 모델링해줘 가장 바깥 원형의 지름은 10이고 양각인 선의 굵기는 0.7mm 상하좌우쪽, 그리고 대각선에 있는 양각인 선의 굵기는 0.6 mm 음각은 상하좌우쪽이랑 원형쪽에 0.4mm 대각선쪽은 0.3mm 로해줘 주얼리쪽 장식으로 넣을거라서 두께는 0.7mm로 해주면 돼

Anonymous1773796857

Make a cylinder 12mm high, 26mm outer width, 19mm inner width. Make four holders on the outside, evenly spaced 7mm from the edge, 2mm thick, and 6mm long.

Anonymous1772468288

Черная пластиковая крышка, с защёлками. Матовая. Толщина пластика 1 мм. Габариты: высота 115 мм, ширина 63 мм (передняя стенка) и 68 мм (по краю контура с открытой стороны). Глубина 10 мм. Две верхние защёлки шириной 7 мм, расстояние между ними 23 мм. Нижняя защёлка шириной 10 мм, отступы по бокам по 30 мм с обеих сторон.

Anonymous1773660347

1. 做一个一个2.5mm 厚，305*431mm 大小的板子
2. 板子掏有密密麻麻的 6 边形孔，均匀分布在整个板子上，边缘不用卡死保证排列的美观
3. 六边形孔的边长定义为 7mm，六边形的孔间距为 2mm
4. 在六边形孔六个边，做出“立边”造型，立边的高度为 3.5mm，宽度为 2mm，从底部慢慢收窄，到顶部尽可能薄（按 0.2mm 宽打样）

Anonymous1773583561

a square hollow tube 7,7mm square, 25 mm long. one side 45 mm long

Anonymous1773511258

cilindro de paredes lisas, sin agujeros de 12.7mm de diámetro y 25.4mm de largo , sin letras

Anonymous1773451304

it is a stamp for imprinting into clay. it is a date (4-15-26 but with interpunct instead of dashes) in a stright line and with no edging. the characters should measure approx. 30mm across (total width) and 7mm high with a depth (so that it can be impresioned into clay) of approx. 5mm. it should also have a short "handle" at the rear to hold it by (say 40mm tall)

Anonymous1773252338

Please make a 90mm Round Piece of brushed nickle, I would like it 7mm thick. then recess out a 4mm section in the middle that is 86mm round

Anonymous1773194980

Please make a 7mm thick brushed nickle circle with a 5mm recess. It should be 95mm round

Anonymous1773194980

A minimalist, brutalist signet ring with a geometric design. The ring features a flat, rectangular top face and a thick, solid band. The inner diameter of the ring must be exactly 21mm. The width of the band is 7mm. The finish is brushed matte silver. High precision, sharp edges, clean manifold geometry for 3D printing."

Anonymous1773020428

Generate a 3D model of a transparent rectangular prism bar with a length of 60.7mm, width of 12.3mm, and thickness of 3mm. The surface has a subtle, embossed diamond pattern. One end is slightly rounded with a radius of 1mm, and the other end is a sharp, angled tip. The model should be a solid, manifold mesh suitable for 3D printing. Export as STL.

Anonymous1772505593

Crea la pieza, te puse imágenes de referencia, es un perfume, en la imagen de la esquina inferior derecha vienen especificadas todas las medias es completamente OBLIGATORIO que sigas las medidas, largo: 67.79mm, alto: 93.86mm, ancho: 27.74mm, el diámetro del primer cilindro es : 24.7mm, el diámetro del segundo cilindro (tapa) es de 32.5mm, la altura de la tapa es de 15.4mm

Anonymous1771029983